Cerakote®

Price List Disassembly / Reassembly Is always on top of the Cerakote® coating prices.
It usually ranges between $45 – $125 depending on the Gun and difficulty.
Although some… Such as the Springfield XD – $200 and the Springfield XDM – $250
So if your worried about your firearm please Call for accurate pricing.

We have a $50.00 Minimum.
At the present time we are running between 1-2 weeks out on single or multi color jobs already broken down.
We are also running about 4 weeks + on design jobs and some jobs that require brake down and reassembly
Gunsmith work can range between 4 weeks depending on the project.
Laser Engraving work can range from same day to 12 weeks +, again depending on the project.
These time frames are AFTER we receive your project in the shop.

We do try to carry most Cerakote® colors but unfortunately we cannot carry every single one they make.
That being said, Cerakote® colors that we do not normally stock will add an additional $55 to your order.

HANDGUN / PISTOL CERAKOTE PRICING:

Slide Only – One Color (stripped) $95.00
Frame Only – One Color (stripped) $95.00

Complete Handgun – One Color $200.00
Complete Handgun – Two Colors $250.00
Complete Handgun – Three Color $300.00
Complete – Custom design up to 3 color $350.00 + Add stenciled charge below
Broken down Slide and Frame same color – $175.00
Broken down Slide and Frame different colors – See slide and frame price at top
Add Camo pattern (Three colors) $95.00
Slide only most design’s including flag – $170.00
4 Color Kryptek pattern Complete + up to 2 mag bases $395.00
3 Color SnakeSkin pattern Complete + up to 2 mag bases $295.00
Distress Add- $50.00

Theme type pistols
These usually run between $300.00 to $500.00 And up depending on number of colors and detail

Accessories or extras for Pistols
Coat Barrel Only with Cerakote DFAC (Includes barrel bushing on 1911’s) $75.00
Coat Pistol Magazines – Each (must be one of the colors on gun) $20
Coat Pistol Magazine – Separate Color $30
Hardware Only – $45.00
Polish Barrel – $70.00
Add Clear ( Hi-Gloss or Matte )- $45.00

Sur charges that may get affect pricing on certain designs
Stenciling work – $25.00 Surcharge
Extreme Detail Stencil work – $70.00 Surcharge

AR TYPE RIFLE & SHOTGUN CERAKOTE PRICING:
Autoloading – AR-15/M4 or AK
Complete Gun: Upper and Lower Receivers, Barrel, Handguard, Pistol Grip, Pins, and Controls
Also includes up to 2 mags One color.
( Does NOT Include stock — except on shotgun )

One Color $310.00
Two Colors $375.00
AR-10 and Variants Surcharge – add to AR-15 pricing $50.00
FN-FAL and HK-G3/G33, etc Surcharge – add to AR-15 pricing $50.00

Pieces Only
Shotgun Metal Only $210.00
AR Upper and Lower Receivers Only – One Color (Stripped) $175.00
Upper Only or Lower Only – $95.00
AR Upper and Lower Receivers Only – up to 4 color camo + Stencil charge (Stripped) – $350.00+
Upper / Lower / Handrail Distressed Flag Design – 350.00
Upper / Lower / and Handrail One Color – $275.00
AR10 Upper/Lower/ and Handrail One Color – $325.00
Upper/ Lower/ Handrail – up to 4 color camo ( Stripped) – $450.00+
Forearm only – Rail Type (One Color) $95.00
Forearm only – Picatinny Quad Rail (One Color) $105.00

Camo type designs
Three Color Camouflage Pattern $475.00
Four Color Camouflage Patterns $500.00
Five Color Camouflage Patterns $525.00
Four Color Kryptek Pattern ( Includes the high temp stencil ) 525.00
Camouflage Using High-Temp Stencils – Stencil Surcharge $45.00
Coat 20/30rd AR Magazines camo (each) $45.00

Scopes And Scope accessories
Scope Mounts (One Color) $40.00
Scopes Standard – One Color C-Series $90.00
Scopes Target and Tactical – One Color C-Series (Includes masking of dials, etc) $150.00
Scopes Target and Tactical – Camouflage (costs may vary – call for quote) $175 – $350

Accessories
Barrel – one color $100.00
2 Color Fluted Barrel – $200.00
Stock: Standard A2 or M4 (One Color) $90.00
Stock: Target Adjustable (MagPul, etc) One Color $125.00
Bolt ( Micro Slick) $75.00
Semi-Auto Bolt and Bolt Carrier (AR or AK) Coat with Cerakote Micro slick $75.00
Bipod – Broken down (One Color) $100.00
Bipod – break down and reassembly – $100.00
Magazines – $30.00 each one color Minimum of 3
Pins / Action bits and parts only – $75.00
Extra Color Charges for Accessories (Each Color) $25.00

Bolt Action Rifle CERAKOTE PRICING
Rem 700 and similar – One Color – $250.00 – Does not include Bolt
Bolt Action and Tactical 2nd Color surcharge – add $50.00
Bolt Action and Tactical – Three Color Camouflage Surcharge – add $95.00 to the 2nd color surcharge
Bolt Action and Tactical – Camouflage Four and Five Color Patterns – Surcharge (add to one color base price) $195.00

All metal including bolt – $250.00 – One color
Barreled Action Only – $175.00 – One color
Stock only – $190.00 – One color
Large Tactical Adjustable type stocks – $195.00 – one color
Large Tactical Adjustable type stocks – $310.00 – Camo up to 3 colors
WARNING!!!! WE MUST KNOW IF YOUR STOCK IS FIBERGLASS….
Fiberglass does weird things when baked and we recommend NOT doing anything that is fiberglass….
That being said….. We will coat your fiberglass stocks and parts but you must know that We are NOT responsible for anything that happens to fiberglass parts if you really want them done.

Parts
Coat Bolt to match – $55.00
Coat bolt handle and Polish bolt – $100.00
With Adjustable Tactical Stocks – Surcharge: add to above $35.00
Bolt Action Rifle Magazines – One Color $30.00
Bolt Action Rifle Magazines – Each Additional Color $20.00

Extra Large Bolt action type Firearms
50 BMG Bolt Action Rifles – One Color $450.00
50 BMG Rifles Additional Colors – Each color, add $150.00
AR-30 and similar .338 Lapua and .408 CheyTac bolt action rifles – one color $475.00
Barrett 82A1 and similar semi-auto 50BMG rifles – One Color $600.00
Barrett 82A1 Magazines, ea – One Color $45.00
Barrett and 50 BMG Magazines – Additional Colors, each: $30.00
Four and Five Color Camouflage Patterns – Surcharge for .338 Lapua Tactical and 50 BMG rifles: – $350.00

SPECIAL WEAPONS:

Suppressor – $95.00
M249, M240, Etc: CALL
Edged Weapons: CALL

*NOTE: Prices are subject to change without prior written notice. Not all firearms are the same and sometimes special circumstances may apply. Toms Custom Coatings will notify the owner of special requirements upon receipt and inspection of the firearm and provide a revised quote before services are performed.

Are you ready to start your coating project? Contact us today to schedule a time.

Tight Tolerance Parts and Markings:

We do not coat sears, springs, bores/chambers or other tolerance critical or high-flex parts. In addition, we do not media blast scopes or other optics and, as a result, there will not be as good an adhesion of the Cerakote to those items.

TOLERANCE: For standard firearms applications it is often inadvisable to coat both pins and pin holes, as the resulting one (1) mil thickness of the coating when applied to rounded surfaces creates increase of two (2) mil to the part tolerance and four (4) mil (.004) when both hole and pin are coated. This is also applicable to auto-pistol slide and frame fit, such as on tight-fitting 1911’s. We typically plug or mask holes and pins and only coat the pin ends. However, we can coat pins and holes and then custom fit these parts after coating for an additional charge. We recommend hand fitting and lapping for 1911 pistol slides and frames as this will yield a precision fit and can help to tighten looser fitting slide/frame combos.

MARKINGS: For receivers, frames, slides, Picatinny rails which have painted on or lightly laser etched markings these markings will be lost during the surface preparation and coating unless they are machine engraved or stamped. If these markings are of great importance we can mask over them, but those areas in and immediately around the markings will not be coated and, as such, will not blend. Manufacturer’s serial numbers will be masked at no additional charge where needed or coated where possible. Some manufacturer model numbers, name etc which are laser engraved will be masked over. This is per BATFE (ATF) regulations. Please consult us for specific requirements.

Cerakote H-Series:
H-Series is the most durable of the standard Cerakote family of coatings and provides the best performance in hardness, wear and scratch resistance, adhesion and rust resistance. It can withstand heat up to 500f – 600f degrees and comes in the widest range of colors. Therefore, we use the H-Series wherever possible. However, it’s a two-part heat cure finish and, therefore, cannot be applied to optics and other items or substrates which cannot, or should not be cured at the required temperatures.

Cerakote™ C-Series:
For high-temp applications up to 1700°, such as suppressors and machinegun barrels, Cerakote™ C-Series has no equal. It’s available in a wide range of colors to match the overall finish requirement of the firearm or weapons system. We also use C-Series to coat scopes and other optics, as well as fiberglass and items and substrates which cannot be baked. It is not as durable as the H-Series and is less scratch and wear resistant. The primary application is optics, electronics and fiberglass stocks which cannot be hear cured.

Cerakote DFAC™ (Dry Film Anti-Carbon)
Is a dry film ceramic coating with special properties and attributes specially suited to tight tolerance applications and high-wear internal parts, such as bolts, bolt carriers, barrels and 1911 barrel bushings, etc… Cerakote DFAC™ penetrates the metal substrate and therefore adds minimal (.25 to .50 mil) thickness. DFAC™ came out of NIC’s industry leading Micro Dyne automotive and turbine coatings division where it has been used successfully for many years to coat automotive pistons, cylinder walls and turbine blades, etc. Cerakote DFAC™ provides outstanding anti-friction and wear-reduction properties and good rust prevention properties. In addition when applied to certain internal firearms parts, helps to reduce carbon fouling by resisting carbon adhesion, which promotes reduced maintenance, easier cleaning and improved operational reliability. DFAC™ imparts a medium grey to dark grey/black color to most steel substrates. Its primary purpose is one of functionality rather than aesthetics as the parts will “burnish” over time changing the original coated appearance of the parts while maintaining the anti-friction and anti-carbon attributes of the coating.

CERAKOTE STANDARD PERFORMANCE METRICS:

RUST RESISTANCE: Cerakote™ finishes have been tested in salt spray and full emersion and have withstood beyond 3,000 hours in salt spray and hundreds of hours in full emersion testing. These results outperform other finishes by over 10x. This makes Cerakote™ finishes the clear choice for marine environments and other environments subject to high humidity and salt water environments.

WEAR RESISTANCE: Cerakote™ finishes can withstand over 5,000 (5,212) wear cycles per mil (.0001). The Tabor wear test uses an 8″ abrasive wheel applied to a metal plate coated with 1 mil thickness of the Cerakote coating. In addition, Cerakote’s Coefficient of Friction is 80% less than stainless steel against stainless steel. So, when one or both moving parts of a firearm are coated you can expect a significantly longer product duty cycle or service life.

ADHESION: Cerakote finishes have an ASTM D3359 rating of 5B and can withstand a 180° mandrel bend rotation test around a 1/4″ mandrel and a ball bearing impact test of 160 inch-lbs with no cracking or loss of adhesion. This is significant performance given Cerakote’s 9H pencil hardness, which is the highest hardness rating in the scale.

HARDNESS AND SCRATCH RESISTANCE: ASTM D3363 is a 9H pencil hardness and 6H scratch resistance.

FILM THICKNESS: 1.0 mil (Cerakote DFAC “Dry Film Anti-Carbon” is .25 to .50 mil)